features surge overload rating -150 amperes peak ideal for printed circuit board reliable low cost construction utilizing molded plastic technique the plastic material has ul flammability classification 94v-0 mounting postition:any maximum ratings and electrical characteristics characteristics symbol unit maximum recurrent peak reverse voltage v rrm v maximum rms voltage v rms v maximum dc blocking voltage v dc v maximum average forward (with heatsink note 2) rectified current @ t c =100 (without heatsink) peak forward surge current 8.3ms single half sine-wave super imposed on rated load (jedec method) maximum forward voltage at 4.0a dc v f v maximum dc reverse current @ t j =25 at rated dc blocking voltage @ t j =125 i 2 t rating for fusing (t<8.3ms) i 2 t a 2 s typical junction capacitance per element (note1) c j pf operating temperature range t j storage temperature range t stg notes: 1.measured at 1.0mhz and applied reverse voltage of 4.0v dc. 2.device mounted on 50mm*50mm*1.6mm cu plate heatsink. 500 93 45 -55 to +150 i r a -55 to +150 rev. 1, 18-oct-2013 a 0.95 10.0 600 420 a 600 i fsm 120 i (av) 4.0 2.4 4GBJ406F glass passivated reverse voltage - 600 volts forward current - 4.0 amperes bridge rectifiers 4GBJ406F dimensions in inches and (milimeters) rating at 25 ambient temperature unless otherwise specified. single phase, half wave ,60hz, resistive or inductive load. for capacitive load, derate current by 20% 4gbj ?.134(3.4) ?.122(3.1) spacing .303(7.7) .287(7.3) .287(7.3) .303(7.7) .303(7.7) .287(7.3) ? .122(3.1) ? .134(3.4) .023(0.6) .031(0.8) .114(2.9) .098(2.5) .150(3.8) .134(3.4) .173(4.4) .189(4.8) .382(9.7) .366(9.3) .157 (4.0) .669(17.0) .708(18.0) .150(3.8) .130(3.3) .074(1.9) .059(1.5) .035(0.9) .043(1.1) .083(2.1) .069(1.7) .041(1.05) .057(1.45) .578(14.7) .602(15.3) .995(25.3) .983(24.7) - ~ ~ + .118(3.0)*45
rating and charactertic curves 4GBJ406F rev. 1, 18-oct-2013 fig.1-forward current derating curve case temperature, c average forward current amperes 75 125 150 0.0 1.0 5.0 100 50 25 3.0 4.0 2.0 single phase half wave 60h z resistive or inductive load with heatsink without heatsink number of cyclets at 60hz peak forward surge current, amperes fig.2-maximum non-repetitive surge current 0 10 100 0 25 50 100 2 50 20 5 75 125 150 single half-sine-wave (jedec method) t j =25 c half-sine-wave (jedec method) instantaneous forward voltage,volts instantaneous forward current,(a) fig.4-typical forward characteristics 0.01 0.1 1.0 10 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 t j =25 c instantaneous reverse current, (ua) fig.5-typical reverse characteristics percent of rated peak reverse voltage,(%) 100 10 1.0 0.1 0 40 60 80 100 120 140 20 1000 t j =150 c t j =125 c t j =100 c t j =25 c fig.5-typical junction capacitance reverse voltage,(volts) capacitance,(pf) 10.0 100 1.0 10 100 50 t j =25 c,f=1mh z
|
